This toner refill kit is used to refill the cartridge most frequently found in the Samsung SF-5100/SF-555P/ ML-1710 90g.

Samsung SF-531/530/531P/5100/CF-5100/Msys 5100P/5100 90g.

This toner refill kit is used to refill the cartridge most frequently found in the Samsung SF-5100/SF-555P 90g.

2 Bottles

This toner refill kit is used to refill the cartridge found primarily in the Samsung SCX 4016, 4116, 4216F

2 Bottles

This toner and developer refill kit is used to refill the toner cartridge most frequently found in the Sharp AL-1000 and the Xerox XD-100. Sharp AL-1000 / Xerox XD-100 Toner Cartridges Sharp Cart. # AL-100TD, Xerox Cart. # 6R914 OEM Stated Yield: 6,000 The standard AL-100TD, and 6R914 cartridges are not interchangeable. They have Oblong tabs on the backside of the cartridges that are in different locations. These tabs block the use of one brand in the others machine. They can be made to be interchangeable by cutting off the tabs, and sealing up the hole. See our cartridge recycling instructions for detailed information. These cartridges also do not have any type of reset. There is a sensor inside the cartridge that measures the mixture of toner to developer. As long as there is enough toner for a good mixture level, the toner lamp will stay off. There are no page counters or "Killer Chips" for these cartridges. There are other versions of these cartridges however that do have "Killer Chips". The following are the current Sharp AL-1000 Engine based cartridges that also have the chips in them. Sharp AL-1000 / Xerox XD-100 OPC Cartridges Sharp Cart. # AL-100DR, Xerox cart. # 13R551 OEM Stated Yield: 18,000 Both of the above cartridges are different, and not interchangeable but the reset procedures are the same. (These procedures are the same for the XC-800/Z-835 copier OPC cartridges). These cartridges are the most popular. There are also other cartridges that use the same supplies, but are physically different. There are tabs on the top of the cartridge that block installation into another brand copier. These tabs are different for each cartridge type. If the cartridge is not a "Starter cartridge", there are two white gears inside the green end cap. On the large white gear, remove the clip ring and turn the gear back to the start position. (This is so the actuator (or flag) is next to the small gear). On some cartridges the "flag gear" is now black. It is located to the bottom right of the white gear. Make sure that when you snap the green end cap back on, the notch on the small gear lines up with the tab on the large single gear that is on the cartridge. Once everything lines up, snap the end cap in place. This is tricky, take your time! To reset the starter cartridge, or any cartridge through the menu, do the following: Enter the diagnostics menu by turning the machine on, and within 4 seconds, press "CLEAR", "EXPOSURE MODE", "CLEAR", "EXPOSURE MODE". (EXPOSURE MODE is the button on the far left). All of the display will go blank. Using the 10 and 1 buttons (copy quantity), enter "24" press "PRINT", enter "7" press "PRINT" again. The counter is now set to Zero!

This refill kit is used to refill the toner cartridge most frequently found in the Sharp AR-152. Sharp AR-152 Toner Cartridges Sharp Cartridge Part # AR-152NT OEM Stated Yield: 6,500 These cartridges have a "Single Use Killer Chip". This chip shuts down the cartridge after the first cycle so it will be necessary to replace it each time. Replacement chips for these cartridges are now available. The chip is installed in the back of the connector on the cartridge. Sharp AR-152 Developer Sharp Cartridge Part # AR-152DV OEM Stated Yield: 25,000 The developer is rated for 25,000 pages. The default setting on the machine is to keep running even after the 25K pages. That default setting can be set by the dealer to stop at 25K pages. It is considered a dealer option. To clear the developer after a stop, or to reset the counter, simulation 24-06 must be run. To enter the simulation mode, press the "CLEAR KEY", EXPOSURE SELECT KEY", "CLEAR KEY", EXPOSURE SELECT KEY". Press 24 Press 06 Press "PRINT" The developer count is now cleared. Sharp AR-152 OPC Sharp Cartridge Part # AR-152DR OEM Stated Yield: 25,000 Inside the drum cover, there is a gear with a "Flag" on it. Remove the gear and place it so the flag is at the 12:00 position. This flag when the cartridge is installed, will turn down, and engage a switch in the machine. This tells the machine there is a new drum. If the drum unit has never been rebuilt, this flag gear is not there. It can be ordered from Sharp, but there is also a reset that can be done through the menu. To clear the drum count if the flag gear is not present, simulation 24-07 must be run. To enter the simulation mode, press the "CLEAR KEY", EXPOSURE SELECT KEY", "CLEAR KEY", EXPOSURE SELECT KEY". Press 24 Press 07 Press "PRINT" The drum count is now cleared.

This refill kit is used to refill the toner cartridge most frequently found in the Sharp AR-160. Sharp AR-160 OPC Sharp Cartridge Part # AR-200DR OEM Stated Yield: Inside the drum cover, there are two white gears. The larger gear has a white tab that must be placed at the 12:00 Position. The smaller gear has two small tabs that must also be place at 12:00.

This refill kit is used to refill the toner cartridge most frequently found in the Sharp AR-163. Sharp AR-163 Toner Sharp Cartridge Part # AR-201NT OEM Stated Yield: 13,000 These cartridges have a "Single Use Killer Chip". This chip shuts down the cartridge after the first cycle so it will be necessary to replace it each time. Replacement chips for these cartridges are now available. The chip is installed in the back of the connector on the cartridge. Sharp AR-163 Developer Sharp Cartridge Part # AR-201ND OEM Stated Yield: 30,000 The developer is rated for 30,000 pages. The default setting on the machine is to keep running even after the 30K pages. That default setting can be set by the dealer to stop at 30K pages. It is considered a dealer option. To enter the simulation mode, press the "CLEAR KEY", "INTERRUPT KEY", "0" KEY", "INTERRUPT KEY", "MAIN CODE" "START KEY", "SUB CODE" "START KEY", "Main code" for clearing the developer = 42 "SUB CODE" for clearing the developer = 1 The developer count is now cleared. To exit the simulation mode press the "CLEAR ALL KEY" Turn the machine off and on. Sharp AR-163 OPC Sharp Cartridge Part # AR-201DR OEM Stated Yield: 30,000 Inside the drum cover, there is a gear with a "Flag" on it. Remove the gear and place it so the flag is at the 12:00 position. This flag when the cartridge is installed, will turn down, and engage a switch in the machine. This tells the machine there is a new drum. If the drum unit has never been rebuilt, this flag gear is not there. It can be ordered from Sharp, but there is also a reset that can be done through the menu To enter the simulation mode, press the "CLEAR KEY", "INTERRUPT KEY", "0" KEY", "INTERRUPT KEY", "MAIN CODE" "START KEY", "SUB CODE" "START KEY", "Main code" for clearing the developer = 24 "SUB CODE" for clearing the developer = 7 The drum count is now cleared. To exit the simulation mode press the "CLEAR ALL KEY" Turn the machine off and on.

This refill kit is used to refill the toner cartridge most frequently found in the Sharp AR-250/405 710g.

This refill kit is used to refill the toner cartridge most frequently found in the Sharp JX-9200 70g. Sharp JX-9200 OPC The Sharp JX-9200 engine has many variations. The known reset procedures are listed by machine model #, and cartridge part #. Sharp FO-26/28/29/AL-80 Sharp Part # FO-26DR/28DR/29DR/AL-80DR OEM Stated Yield: 20,000 (All) These cartridges do not use any reset procedures at all. According to the Sharp manual, they should be replaced when the copy quality deteriorates. No codes will show on the display to change the cartridge. NOTE: None of these cartridges are interchangeable, they all are slightly different. Sharp AL-800 Sharp Part # AL-80DR OEM Stated Yield: 20,000 Open the front cover, and turn the power on. While pressing and holding both the "Exposure mode" and the "Clear key", close the front cover. Continue to hold these keys for 5 seconds, until the drum light goes out. Xerox XE60/80 Xerox Cartridge Part # 13R553 OEM Stated Yield: 18,000 With the power on, open the front door. Hold the "Copy Contrast" button while closing the front door, continue holding the button down for 3 seconds, then release. Sharp JX-9500 OPC / Toner Sharp Cartridge Part # JX-95DR OEM Stated Yield: 50,000 OPC, 25,000 Toner There is a glass fuse located under a clip on the top of the cartridge. Replace the fuse each cycle. The fuse is a 250V, 80mA, 5x20mm fast acting glass type. The toner waste bottle also uses a fuse- a 250V, 50Ma 5x20mm fast acting glass type.

This refill kit is used to refill the toner cartridge most frequently found in the Sharp Z835 170g toner 165g developer. Sharp Z-835 / Xerox XC-800 OPC Cartridges Sharp OPC Part # ZT81DR , Xerox OPC Part # 13R544 OEM Stated Yield: 20,000 Both of the above cartridges are different, and not interchangeable but the reset procedures are the same. (These procedures are the same for the XD-100/AL-1000 copier OPC cartridges). If the cartridge is not a "Starter cartridge", there is a small gear with a flag on it located on the gear side of the cartridge bottom right. Remove the gear and replace so that the flag is at the 1 O’clock position. If this gear is missing, the cartridge is a starter cartridge, and the following procedure must be used. To reset the starter cartridge, or any cartridge through the menu, do the following: Enter the diagnostics menu by turning the machine on, and within 4 seconds, press "CLEAR", "EXPOSURE MODE", "CLEAR", "EXPOSURE MODE". (EXPOSURE MODE is the button on the far left). All of the display will go blank. Using the 10 and 1 buttons (copy quantity), enter "24" press "PRINT", enter "7" press "PRINT" again. The counter is now set to Zero!

This refill kit is used to refill the toner cartridge found primarily in the Tektronix 540/560/740/750, Color 150g, Black 200g.

Tektronix Phaser3400B/3400N 190g.

This refill kit is used to refill the toner cartridge found primarily in the Xerox 1012 400g. The 1012 OPC cartridges look very similar to the5011 and 5012, but they are different and NOT interchangeable. There are now many different Xerox part numbers for these cartridges. They are interchangeable, just sold from different sources. A list of some of them is as follows: 13R8 (US), 13R10, 13R30, 113R92 (Retail Stores), and 13R500. This cartridge uses an optical reset similar to the Panasonic 4410. The waste chamber must be spotless, and the float in the down position. There is a clear plastic bubble on top of the cartridge. This is what the sensor looks at and it must be spotless! The J7 code is triggered when the waste chamber fills up and moves the float into the bubble, interrupting the optical sensor.

This refill kit is used to refill the toner cartridge found primarily in the Xerox 1025 227g.

This refill kit is used to refill the toner cartridge found primarily in the Xerox N24/32/40 1075g. Xerox N24 / 32 / 40 OEM Stated Yield: 20-23,000 (Depending on cartridge) This engine has more non-interchangeable cartridges than any engine I have ever seen. All of them use a "ARD" that is built into the connector. Almost every type of cartridge has it's own individual ARD. Since every individual cartridge has it’s own chip, it is imperative that you have the OEM cartridge part number when ordering the chips! The reset boards are now available with the plastic housing so that soldering the chip in is no longer necessary. There are also services where you can have the old chip reset. There are still cartridges that do not have replacement chips available yet. These are mainly international, but not all.